Відео

Methylene chloride is a known carcinogen

Awesome! What resin did you use?

hi what software is this

Great video, but you seem a little flustered throughout the beginning of the video which was a bit distracting with all heavy breathing and the fidgety, shakey hands. Just relax, you got this 😊

good video .thanks a bundle 😁

Did you have to thin the "Mirror" paint before spraying?

si you have other recommendations? it’s the best video ever about this topic, straight to the point, you deserve heaven, money and joy

What kind of 3d printer was used to print these heads ?

Do the pictures have to be in order?

Any chance you could try again but do tiny tiny tiny little hexagons? I'm trying to design a suit for a 1/6th scale spider-man figure and wondering if this woud be a good solution for the suit texture.

I tried doing the two colors in my printer. And my printer just ended up mixing the colors up. Do you have it at a low speed setting?

sometimes its best to just put another coat of gloss over the whoel thing, a nice wet coat and let it cure

Hey, just curious, why do video and extract frames, instead of taking photos?

Pro tip: mix up some regular resin like smooth-on, pour it in the hollow print and then roto-cast it by hand. Do a little bit at a time. This will help cure whatever resin residue left. Do this a couple of times. Let it set for a few hours until it’s fully cured. THEN use plaster to fill it up. Your welcome.

That's great! 🔥🔥🔥

what software you're using for scan build?

Came here after my first print. Going to swap this out for a Fresnel lens printer. See if it's any better.

I had the same problem, very annoying. Fixed it with a lift speed decreasing.The print is little bit slower but the result is great.

Very nice demo. How did you print out the images, what kind of printer did you use?

Nice!

That’s impressive. Thanks for the content.

Это ЖЩЦЧ какой то)

Nice but I prefer Meshroom. Stick to the defaults and there's nothing else to do except deleting a few unwanted faces afterwards.

Very insightful! Thnaks a lot !

what air brush did you use

Didnt work guess the pla material isn't the same

It might help if you followed the instructions. It is meant to be BRUSHED on VERY thinly, almost as a dry brush. Less is more. The thinner the coat, the better the gloss. It also says specifically it should not be sprayed.

How did you get enough images of pierce morgan to create a 3d model? Cant imagine u doin a 360 on him 😂

I tried and tried but failed miserably. The results were so bad I could not 3d print. I was hoping that by now this technology would have progressed but sadly it is still in tge primite stages

This is incredible!! You stumbled on how to make your prints look injection molded. I might just mod my Saturn to do this.

Great video. With all the AI and Lidar and Apps available today, this method while very time consuming, appear to be giving the best results. I hope it works to objects too I'm going to try it on an antique violin that I need to scan.

we just see nothing of this repair tips! it s useless content

also- for 3d printing are you using a fillament or resin? I'm interested in doing figures of photos

Could you do a video of a full body scan? Also, if the person that is being scanned lives in another country- do you provide them with instructions on how they need to do the pictures?

it could also mean u need lube on ur rails

AMAZING!

Nice work I’m trying to learn to do it. I got many people asking to make they dead ones.

Nice results, I’m just getting into electroforming i hope to get the same finish as you one day

Hi, what filament have you used in the girl head at the end of your tutorial?

What kind of 3D Printing machine do you have

Your video shows the BASICS, but you should have shown HOW you clean up areas of the model. Just showing Before and AFTER does absolutely NOTHING...

they said it cannot be done, good job

That's suction force on this them sunken blurred lines these will disappear on hollowing and angling and lowering the layer hight! I have had the grid lines print on a large print they print the squares not just lines so this is not the grid lines it's suction to maybe angle or loose streched fep!. Anycubics mono 4k prints the grid same as your cutting mat on larger prints

5:48

What is that tablet your using called?

Your talking very fast and not showing exactly what ir clinking on keep in mind not everyone is as experienced as ypu may be with thos program also move the mic away from your face or vise versa

did you ever finish it?

...or put some lubricant on your fep.

Acetone does not chemically react with PLA. Ethyl Acetate looks promising I wonder if it can make Clear PLA more clear ?!?

Alcohol base window cleaner works wonders, I have even used homemade alcohol based window cleaner with white vinegar and it works just fine.